DIY Network has step-by-step instructions on installing tongue-and-groove subflooring planks. . If you are remodeling and find that some areas of the subfloor are damaged, consider replacing them with new tongue-and-groove boards. . Place the groove of the next board over the nailed tongue, covering the nails
plywood panels should be tongue-and-groove or supported with blocking with the following exceptions: where a separate underlayment (1/4 inch minimum thickness) (see previous page) is to be installed with its joints offset from those in the subfloor;. a minimum of 1-1/2 inch of lightweight concrete is to be applied over..
Sep 4, 2013 . Now I have moved on to the other half of the basement -- a family room -- but I have used XPS on the walls and on the floor as well using a method of floating 5/8-inch plywood over 1-inch XPS. I did not use sleepers, but attached the plywood directly to the slab with split drive anchors through the XPS
Because the edges of this CDX plywood are tongue and grooved they interlock to each adjoining sheet providing a strong secure base for any finished flooring. To prevent hearing squeaks later through the finished flooring I highly recommend applying a thick bead of subfloor adhesive caulking to the top of the floor joists..
Mar 8, 2016 . I finished my plywood plank ceiling and I LOVE it! V Groove Plywood Plank Ceiling. I wanted to cover my studio ceilings with pine tongue and groove planks like I've done in most of the main level of my house. I'm able to get Pine tongue and groove planks for about $2.25/sq ft so it was going to cost about..
Oct 13, 2011 . When you are going 44 feet wide, if you get off 1/8" here, 1/4" there, a hair over there . you'd be surprised at how fast that can add up to inches! Step 3 Diagram: Step 3 Instructions: For subflooring, you use tongue and groove plywood. The tongue and groove are only along the 8 foot edges. On the four foot..
However, we have discovered since then that it would be cheaper to do tongue and groove 3/4" pine (the back side of wainscoting, which is the flat side, would be up - we plan to do the ... And, I believe they use a permanent marker, like a Sharpie, to d lines to give the plank look - and then they stain & poly over that
Engineered wood flooring is a prefinished tongue-and-groove flooring that has alternating wood grain laminations much like plywood, but with a 1/8-in. or thicker solid . The thin profile of engineered wood flooring makes it a great candidate for remodeling because you can install it over an existing floor without significantly..
Mar 16, 2017 . For his wood-plank ceiling, DIY homeowner Keith Lively chose solid tongue-and-groove pine flooring with a beadboard pattern. . To avoid the problem of locating the end joints on exact joist spacing, Lively installed a layer of plywood over the joists just like a subfloor, which provided a flat, level and..
Mar 30, 2015 . Bob talks with carpenter Bob Ryley and general contractor Kevin Kalman, as they lay down the subflooring
Apply wood glue to the tongue and groove seams, then connect the pieces, carefully folding and tapping the new piece to rest on the subfloor. Immediately . Use small pieces of painter's tape randomly over each new seam to secure your work as you move. This provides . Glue-down Installation over a Concrete Subfloor..
Sturd-I-Floor. APA Rated Sturd-I-Floor is a combined subfloor-underlayment product designed specifically for single-layer floor construction beneath carpet and pad. When other finish floor products are used, builders often install a separate underlayment grade of plywood over the subfloor
Whether you select bamboo hardwood or engineered bamboo planks, the flooring comes with tongue-and-groove fasteners that make it simple for do-it-yourselfers to install a floating floor. It's also possible to glue or nail down bamboo, but those installations are best left to the professionals. Before you install bamboo over..
Feb 10, 2014 . Also, it is twice the cost of regular subfloor adhesive, but you can actually use less. Since there is no "skin" that will form that will need to be broke again by the laying of the plywood over it, to squeeze the glue again out of the skin that was formed by it sitting open before the plywood goes down. Do not drop..
Feb 23, 2010 . What may be a surprise, though, is that a tongue-and-groove subfloor, the typical base in old-house floors, and even common construction plywood or . Instead, for the past 25 years or so, the standard method for setting tile floors has been over a modern-day simulacrum of a mud job generically called..
CDX plywood and screw it to the subfloor with 1-5/8 in. drywall screws spaced every 4 in. 3/4-in. tongue-and-groove plywood or OSB (oriented strand board). No extra layers of underlayment are required. Just screw the floor down with 1-5/8 in. drywall screws spaced every 6 in. Vinyl flooring glued over 1/4-in. underlayment
Nov 26, 2014 . Often used to install subflooring over framing joists, tongue and groove plywood creates a stable base and is surprisingly easy to install. You'll find that there are many types of tongue and groove plywood available, including those manufactured specifically for decking, subfloor, and siding projects
Instructions on how to prepare a wood subfloor before installing hardwood flooring
Sep 5, 2014 . If you have ever lived with a non-tongue/grove plywood (or chipboard) subfloor, the answer will be obvious: it is to prevent squeaking, creaking, and grinding from people walking over it. Squeaking may be a symptom though, even though it can be darn annoying. The squeaking caused by the plywood..
Dec 13, 2017 . We will also review other flooring options as well, such as OSB subfloor and tongue and groove subfloor for your basement. By the end of the review, you should be able to . But there are several reasons why many contractors still prefer DRIcore over plywood subflooring. Related: Exploring the Value of a..